ASTM D4674 暴露在室內辦公室環境下的塑料顏色穩定性加速試驗的標準實施規范（暴露在室內熒光燈和透窗入室日光下的塑料顏色穩定性加速試驗的標準試驗方法）

ASTM D4674-2002發行信息

標準號ASTM D4674-2002a(2010)

中文名 暴露在室內熒光燈和透窗入室日光下的塑料顏色穩定性加速試驗的標準試驗方法

英文名 Standard Practice for Accelerated Testing for Color Stability of Plastics Exposed to Indoor Office Environments

發布日期2002

實施日期

廢止日期無

中國標準分類號G31

國際標準分類號83.080.01

發布單位US-ASTM

代替標準No Replacement

ASTM D4674-2002適用范圍

根據本實施規程進行的試驗旨在引起與典型辦公環境中的光照和熱暴露相關的性能變化。這些暴露不是為了模擬局部現象（如搬運、污垢污染等）造成的劣化。

附注58212；警告：警告：有關適用于所有實驗室風化裝置的完整警告指南，請參考規程G151。關于可變性來源以及通過實驗室加速暴露試驗的設計和數據分析解決可變性的策略的更多信息，請參見指南G141。

本實施規程中描述的不同方法之間可能存在結果差異。例如，所用燈具光譜分布的差異和單個燈具輻照度的變化可能導致試驗結果的顯著差異。因此，除非附有根據第12節編制的報告，說明需要包括對所用方法的引用，否則不得提及本慣例的使用。

當根據與其他材料或?qū)φ瘴锵啾鹊男阅艿燃壴u估材料的穩定性時，實驗室間試驗結果的再現性已被證明是良好的。因此，強烈建議在試驗材料的同時暴露具有已知性能的類似材料（對照）。建議對每種材料至少進行三次重復，以便對結果進行統計評估。

Tests conducted in accordance with this practice are intended to induce property changes associated with use exposure to light and heat in typical office environments. These exposures are not intended to simulate the deterioration caused by localized phenomena such as handling, dirt contamination, etc.

Note 58212;Caution: Caution: Refer to practice G151 for full cautionary guidance applicable to all laboratory weathering devices. Additional information on sources of variability and on strategies for addressing variability by design and data analysis of laboratory accelerated exposure tests is found in Guide G141.

Variation in results may be expected are possible between the different methods described in this practice. For example, differences in spectral distribution of the lamps used and variations in the irradiance for a single type of lamp can cause significant differences in test results. Therefore, any no reference to the use of this practice should be made unless accompanied by a report prepared in accordance with Section 12 that describes needs to include a reference to the method used.

Reproducibility of test results between laboratories has been shown to be good when the stability of materials is evaluated in terms of performance ranking compared to other materials or to a control. Therefore, exposure of a similar material of known performance (a control) at the same time as the test materials is strongly recommended. It is recommended that at least three replicates of each material be exposed to allow for statistical evaluation of results.

1.1 This practice covers the basic principles and operating procedures for using fluorescent light to determine color stability of plastics when materials are exposed in typical office environments where fluorescent overhead lighting and window-filtered daylight are used for illumination and where temperature and humidity conditions are in accordance with American Society of Heating, Refrigerating, and Air-conditioning Engineers (ASHRAE) recommendations for workers'' comfort.

1.2 This practice describes four methods where specimens are exposed to fluorescent light under controlled environmental conditions. Two of the methods use an exposure device that provides for mixing of fluorescent lamps and two of the methods use devices that comply with Practice G154.

Note 18212;Method I uses cool white fluorescent lamps and window glass filtered fluorescent UVB lamps and is the same method described in previous versions of this standard.

1.3 Specimen preparation and evaluation of the results are covered in ASTM methods or specifications for specific materials. General guidance is given in Practice G151. More specific information about methods for determining the change in properties after exposure and reporting these results is described in Practice D5870.

1.4 The values stated in SI units are to be regarded as the standard.

1.5 Unless otherwise specified, all dimensions are nominal.

1.6 This practice may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, is any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practi......